Products By Engine
Products By Category
- Cam Belt Change
- Cylinder Head Refurbishment
- Cylinder Block Refurbishment Tools
- Oil & Fuel System
- Wheel Bearing / Suspension Tools
- Clutch / Flywheel change
- Drive/Prop Shaft & Diff Tools
Navigation
Twin Cam Engine (8V)
Alfa Romeo Twin Cam engine is an all alloy 4 cylinder engine produced from 1954 to 1994.
Introduced in the 1290 cc Giulietta in 1954, the capacity was increased to 1570 cc with the introduction of the Giulia in 1962. The twin cam engine was later increased to 1779 cc in 1968.
The 1962 cc engine was introduced in 1971. The last examples of this engine 1590 cc, 1750 cc and 1995 cc went into production in 1985.
Available Products
Essential if you are thinking of removing the clylinder head on your twincam engine. More details
£26.21
Montreal V8 & Twincam Cam Cover Retaining Nut Removal Tool
Ideal tool to keep your nuts in perfect condition! More details
£8.98
Twincam & Montreal Valve Removing Tools
This tool has been modeled on a genuine tool. More details
£34.66
Rear Wheel Bearing Retainer Removal Tool - A.5.0187
As well as being a useful tool for 75 models, this tool can also be used on Alfetta Guilietta GTV6 and 90 models. More details
£7.48
Rear Wheel Bearing Retainer Removal Tool - A.5.0239
Do not chance damaging the retainer, use the correct tool for the job. More details
£6.63
Inlet Camshaft Tool - A.5.0232
This tool is a 55mm spanner for the ring nut securing the inlet camshaft sprocket. More details
£6.83
Rear Wheel Hub Removal Tool - A.2.0380
Wheel hub removal tool for Alfetta, Alfasud and 75/Milano Models More details
£26.86
Rear Wheel Hub Removal Tool - A.3.0327
Wheel hub removal tool for Alfetta, Alfasud and 75/Milano models More details
£29.23
Rear Wheel Bearing Removal Tool - A.3.0432
A real simple method of extracting the rear wheel bearing. More details
£24.82
Twincam Camshaft Locking Tool - A.2.0423
This tool is for clamping the valve timing variator on Twincam engines fitted with them. More details
£19.71
Gearbox and Differential 12mm A/F Hex Key
Alfa Romeo gearboxes and differentials use 12mm or 14mm filler plugs. More details
£13.21
Twincam & Montreal's V8 TDC Gauge Holder Tool
A TDC gauge holder is an essential tool for timing your engine. More details
£22.36
Spica Fuel Injection Adjustable Dummy Thermostatic Actuator
This setting tool is designed so that it can be set to any of the specific lengths required to set and mantain your Spica fuel injection system. More details
£30.70
Spica Fuel Injection Dummy Thermostatic Actuator - A.4.0158
Fixed length TA tool - 27mm More details
£30.70
Spica Fuel Injection Dummy Thermostatic Actuator - A.4.0119
Fixed length TA tool - 28.7mm More details
£30.70
Spica Fuel Injection Dummy Thermostatic Actuators - A.4.0200
Fixed length TA tool - 29mm More details
£30.70
Spica Fuel Injection Dummy Thermostatic Actuators - A.4.0201
Fixed length TA tool - 30mm More details
£30.70
Spica Fuel Injection Pump Pulley Locking Tool
Not much to say about this tool, the title says it all really. More details
£199.40
Crankcase Cigarette Seal Installer
Use this tool to install the "cigarette seals" in the crankcase of Twincam engines. More details
£25.60
Pinion/Crankshaft Nut Tool - A.5.0114
This tool is used to remove the nut on the pinion final drive and the crankshaft nut on the 102, 105 and Montreal (pinion nut only) series engines. More details
£34.18
Twincam Engine Cylinder Liner Retaining Tool - A.2.0117
Simple little tool for holding the liners in place More details
£4.00
Valve Retaining Tool - A.2.0192
TotallyAlfa Alfa Romeo Valve Retaining Tool A.2.0192 More details
£24.86
Valve Retaining Tool - A.2.0121
TotallyAlfa Alfa Romeo Valve Retaining Tool A.2.0121 More details
£17.35
4,6 & 8 Cylinder Flywheel Locking Tool
This tool is ideal if you want to lock the flywheel in position while you are replacing the clutch etc. More details
£8.86
4 & 6 Cylinder Flywheel Locking Tool
This tool is ideal if you want to lock the flywheel in position while you are replacing the clutch etc. More details
£12.15
750 Type Twincam (8 Valve) Valve Removal Tool
I am making this valve removal tool in small batches. This tool have been modelled on a genuine tool. So all of the parts are interchangeable with the original factory tool. More details
£36.25
Latest Blog Entry
Things have have not really gone to plan. Although Wossner assured me that the pistons would fit my engine if seems that their version of fitting and my version differ. ...